Wafer Thinning Acceptance: How to Specify Thickness and TTV

Nov 06, 2026

Leave a message

HISEMI / WAFER PROCESS QUALIFICATION

Wafer Thinning Acceptance Starts with a Measurement Plan

Define where thickness will be measured, how the wafer will be supported and which results must pass before you approve the process.

A wafer comes back from a trial with the requested thickness at its center. The buyer is ready to sign off until the process team asks for the thickness near the edge. The report contains one number and no map. The supplier may have met the instruction it received, while the buyer still has too little information to release the wafer to the next operation.

Agree on the measurement plan before sending samples for wafer thinning. A drawing with a nominal thickness is a starting point. Add the statistic that will be compared with the tolerance, the area included in the measurement and the stage at which the result will be accepted. Put those details on the same sheet that goes to the supplier and your own metrology team.

Hisemi precision lapping and polishing machine for wafer processing

Hisemi precision lapping and polishing equipment. Confirm the fixture and sample configuration in the proposal.

01 / Give final thickness an explicit acceptance rule

Start with the dimension the next process actually needs. Ask whether the target applies to the center, the mean of the specified points or every valid point on the wafer thickness map. These rules can produce different decisions from the same data. If a downstream step has a minimum local thickness, put that requirement on its own line rather than expecting a mean value to protect it.

Write the units and the reporting precision next to the tolerance. Tell the supplier whether the dimensions apply immediately after lapping or after polishing, cleaning and release from the carrier. If several operations remove material, identify the intermediate target and final target separately. That gives the process engineer a basis for allocating the remaining removal allowance without having to infer it from the finished drawing.

Include the incoming thickness range on the sample sheet. Two wafers ordered to the same final dimension may arrive with different starting thicknesses or profiles. Record the incoming condition for each sample ID so the team can explain why one part required a different amount of removal.

02 / Compare total thickness variation with the thickness limit

For a defined set of valid thickness readings, total thickness variation is the maximum reading minus the minimum reading. When a map is sampled at discrete points, the calculation describes those points under the agreed measurement recipe. Include the map or point data with the reported value so the buyer can see which locations set the result.

Hypothetical comparison using three readings per sample
Sample Readings Mean thickness TTV
A 99, 100, 101 µm 100 µm 2 µm
B 96, 100, 104 µm 100 µm 8 µm

Both samples average 100 µm, but Sample B spans a wider range. If a hypothetical order requires every valid reading to fall between 98 and 102 µm, Sample A meets that condition and Sample B falls outside it. A TTV limit alone would leave a different question unanswered. A uniformly thin wafer can have a small thickness range while its readings fall below the required absolute thickness.

03 / Put measurement points and edge exclusion on the drawing

Ask for the coordinates or map recipe used in the wafer TTV measurement. Show the wafer orientation, the reference notch or flat if applicable, and the boundary of the valid measurement area. If your order uses an edge exclusion, state the distance and how it is measured. When the usable area extends close to the edge, review whether the proposed map actually covers the region your next operation will use.

A short point pattern can help a laboratory screen early samples. A denser map can reveal variation between those points. If the supplier uses one method and your receiving team uses another, agree on a comparison before setting a limit. A result obtained from a few agreed points and one obtained from a wider map should retain their own measurement descriptions in the report.

Set out how missing readings will be handled. If a location gives an invalid result, the report should show which location was affected and whether it was remeasured or omitted under the agreed procedure. This matters when a missing point sits near a region where thickness changes quickly. The buyer should be able to see the coverage that remains after exclusions.

04 / Agree on what the instrument measures

Identify the substrate and any layers, protective films or carriers that will be present during measurement. If the wafer is temporarily bonded, ask whether the reported value is for the substrate or the full stack. Record whether the wafer was supported, chucked or measured after release. Give the supplier a sample drawing if the measurement has to distinguish one layer from another.

Ask the metrology team to confirm which instrument and setup suit the material and expected thickness. Record the instrument, recipe and support conditions for the acceptance measurement. If the buyer and supplier use different instruments, measure a common sample before relying on their results for a tight tolerance. Investigate a persistent difference with both teams before changing the machining process.

Request bow, warp or surface finish as separate results when the project needs them. KLA lists thickness variation, flatness and bow or warp as separate wafer geometry outputs. A thickness map answers how the distance between the two surfaces varies over the measured area. The geometry and finish reports answer other questions about the condition of the wafer. KLA wafer metrology overview

05 / Match the fixture and process to the actual sample

Hisemi's Precision Lapping and Polishing Machine page lists acceptable wafer sizes of 3, 4 and 6 inches, plate diameters of 300, 350 and 420 mm, and SJ and ASJ jig types. Use these catalogue details to start the equipment discussion. Ask which plate and fixture the supplier proposes for your wafer material, dimensions and processing stage. Hisemi machine specifications

Send the usable surface dimensions as well as the overall diameter. Mark any areas that must be protected from contact or material removal. For a fragile or irregular sample, include a drawing and explain how it will be transferred between steps. Ask the supplier to describe the proposed holding method and which measurements will be taken before and after release.

Agree on the report for edge condition before sending valuable samples. Specify which areas are inspected, how defects are recorded and which reference images will be used for comparison. Identify pre-existing marks on the incoming sample. If damage appears during the trial, the record should show when it was first observed and which operation preceded the inspection.

06 / Use the pilot batch to check repeatability

Once an initial wafer thinning trial meets the agreed criteria, decide what the pilot batch needs to demonstrate. Give every wafer a sample ID and keep the incoming and outgoing maps linked to it. Review within-wafer variation separately from the differences in final thickness across wafers. A series can show a narrow thickness range on each wafer while the mean thickness shifts between samples.

Before the trial starts, agree on the number of samples, the decision rule and how rework will be recorded. If a process adjustment is made after the first few pieces, identify the wafers run before and after that change. This gives the buyer a basis for comparing like conditions and helps the supplier repeat the accepted process on later samples.

Ask for one report package containing the sample IDs, measurement conditions, maps, exceptions and a disposition for each piece. For an equipment purchase, agree which items the supplier will demonstrate during the application trial and which checks your own team will repeat after installation.

Wafer Thinning and TTV FAQ

Can we approve a wafer from its center thickness?

Use center thickness if that is the agreed requirement. Where the project also limits variation or minimum local thickness, request the agreed map and check those limits separately.

Can two wafers with the same TTV have different thicknesses?

Yes. TTV describes the spread between the highest and lowest valid readings. Keep the absolute thickness results alongside it.

Can we compare reports with different edge exclusions?

Ask both teams to identify a common measurement area and point pattern. Compare results over the same valid area using compatible methods.

Should the wafer be measured before or after debonding?

Specify the state that matters to the next operation. If both stages are important, request separate records and identify the support conditions for each measurement.

Does the machine's wafer size range establish its TTV capability?

Use the size range to check basic fit. Establish the achievable result for your material, fixture and measurement recipe during the agreed trial.

What should we send with a trial request?

Include substrate material, size, incoming thickness, target thickness, TTV limit, edge exclusion and the required measurement state. Add a drawing and any separate finish or edge criteria.

Request a Wafer Trial and Equipment Quotation

Send Hisemi your sample drawing, substrate details and acceptance sheet. Ask us to review the proposed lapping and polishing configuration, fixture options and the measurements to include in the trial report. Add your sample quantity and destination so we can discuss the next step.

Hisemi Technology (Beijing) Co., Ltd.
info@hisemitech.com · WhatsApp +86 139 3415 1273

References

  1. Hisemi Precision Lapping and Polishing Machine specifications
  2. KLA wafer metrology overview
Send Inquiry