PRECISION FIXTURE VALIDATION
A polishing jig qualification should start with the actual workpiece, its contact surfaces and the final finish or geometry requirement. Verify that the workpiece seats repeatably and that the approved setup preserves the features the customer needs. Keep the fit check distinct from the inspected process result. A jig that accepts the nominal outline may still support the workpiece in an unsuitable position.
Hisemi's precision polishing jig is a useful product reference for an inquiry. Ask for a candidate drawing or setup description applicable to your workpiece. Specify dimensions, tolerance, support and material conditions in the same submission. Do not infer a finished-workpiece guarantee from the jig or machine listing.
Use the real geometry, support condition and measurement evidence before and after the process.

View the related product or series · Compare the second product or supplier reference
Mark contact and keep-out areas
Mark where the fixture may support the workpiece, which areas need protection and which side must stay accessible. Include an approved drawing and the physical sample identification. Give the supplier information about the actual starting condition, intended process and relevant edge geometry. If a drawing tolerates several thicknesses or part sizes, identify the sample population rather than demonstrating the easiest one only.
Agree how to identify position and orientation without creating damage. Ask the responsible process owner to review support and retention under the approved setup. Bring an actual production-like specimen where use is authorized. A dummy can help check broad geometry, while the actual workpiece is needed for workpiece-specific issues such as support or cosmetic effects.
| Stage | Evidence to record | Approval question |
|---|---|---|
| Before loading | Workpiece revision, actual dimensions and observed surface condition | Is the sample representative? |
| Setup | Jig drawing, contact marks and agreed orientation | Is loading repeatable under the approved method? |
| Process check | Identified trial configuration and observations | Were the intended conditions used? |
| After unloading | Expected geometry, finish and any marks under the specified method | Did the actual workpiece meet its own criteria? |
| Repeat | Matched fixture and sample references | Can another authorized operator repeat the result? |
Inspect before and after the operation
Select the measures the project actually uses. A process team may need film or finish information, thickness data or documentation of an edge condition. Give each its own measurement method and sample position. Record any pre-existing pattern or damage on arrival. In the final inspection, compare the same region under the appropriate setup rather than assigning a mark to the jig based on a photo taken at a different angle.
Let the responsible owner evaluate unexpectedly different results. Compare the workpiece, approved loading method and specimen orientation first. Record whether a change occurred in the jig, measurement, consumable or process condition. If multiple items changed, use a marked repeat rather than inferring that one operator or part caused the result.
Put requalification conditions on the released drawing
Keep the jig drawing and accepted workpiece scope together. Identify what happens when grinding or polishing conditions, mounting arrangement, material, dimensions or service parts change. A production buyer needs orderable identity, what is included and the reference for the accepted trial. Preserve the scope of acceptance in the record available to purchasing and receiving.
Define the fit decision before introducing a process variable
Ask the fixture owner to identify which features locate the part and which features secure it during the approved setup. Use the exact part revision and show the approved orientation. If the part has an irregular edge or a visible reference, draw it next to the jig marking. Avoid assuming that an operator will see a hidden reference once other pieces of the assembly are in place. Confirm how the setup is checked under the current procedure.
Have a qualified person prove the intended handling on an approved sample before running the application trial. If the buyer is assessing fit at two permitted size conditions, label both and record what was actually placed in the fixture. A visual check can show accessibility, but other criteria may need their own evidence. If a shim, support or consumable is needed for the trial, record its specification and approval. It becomes part of the tested condition.
Ask for an observation that can distinguish two causes
Consider a hypothetical case where the sample sits correctly but an unexpected mark appears after the operation. The useful report identifies whether an equivalent mark was visible before loading, its actual region and appearance, how the workpiece was oriented and any handling deviations. Do not assign the mark to the jig simply because it appeared during the trial. Ask the authorized owners to plan the relevant repeat, and keep the original observations visible.
In a second case, the operator reports that another sample of the same nominal diameter cannot be put into the approved position. Record actual dimensions and any relevant feature difference. Review the sample population and tolerances with the supplier. This is why a pilot sourcing request should ask how the proposed construction covers the agreed range rather than simply quoting a nominal size. Preserve the supplier's marked drawing and any limits on the accepted workpiece.
Write a release that production can use without the trial team
Attach the approved setup reference, workpiece identity, measurement methods and any outcome or deviation that controls the application. Use the qualified set of conditions as a production basis only after the applicable approval. If the trial assessed geometry and fit but not finish or repeatability, leave those items open. Agree how a new production operator can find the identified instructions and check that all parts and fixtures belong to the accepted revision.
Consider which service or replacement conditions reopen the record. An interchangeable-looking accessory with different contact positions, or a workpiece that uses a new protective stack, might change the tested behavior. Ask the supplier which revision information is provided with replacement parts so receiving can compare it with the approval. A test certificate may identify the fixture; the production file should still identify which workpiece and setup it was qualified against.
For the closing file, request one marked photo or drawing for each review point and a short report with a sample identifier. Put incoming condition, fixture, operation and results into separate sections. Ask the reviewer to identify which evidence is necessary for an order and which is exploratory. This structure gives purchasing the right edition and acceptance scope without turning the lab notebook into a purchasing instruction.
A qualification request should state whether the fixture is expected to locate an irregular feature, support a workpiece during a process transition, or mainly carry it to the next approved station. Each purpose can require different evidence. Send a photograph of the actual workpiece alongside the released drawing, particularly when a practical obstruction is hard to see in the drawing. Mark the photos by area to keep before and after images comparable. Ask which interpretation of flatness, finished profile or cosmetic mark applies and which fixture characteristics are checked separately. When there is a variation in geometry, coordinate sample selection with the technical team rather than running whichever piece happens to be at hand. A later buyer can use the accepted conditions for a new order only if the applicability is clear. Put revision, workpiece identity, intended support and sample status on each quote and approval line. Where revalidation is necessary, give the next operator a concise description of the data needed and how to mark each sample. Keep photos that represent an accepted surface and those used only for preliminary discussion separately. If more than one operator conducts the loading check, tell the supplier about differences in the observed setup rather than collapsing them into an average. A polishing jig qualification should keep actual measured outcomes or required records tied to individual samples so a later material change does not automatically inherit an approval from the first trial.
On the sample record, list the accepted method of identifying which side and orientation were measured. If a protective pattern or a reference feature changes after the process, preserve enough context to match old and new observations. A responsible metrology owner can then assess whether the region was compared under equivalent conditions. Ask the lab to identify any row that represents a different instrument or support rather than combining unrelated figures. New acceptance limits should be agreed in a controlled revision rather than added to the presentation after a trial.
Questions on the qualification sheet
Can a standard-size dummy prove the fit?
It can help check the drawn envelope. Use the real approved workpiece to validate application-specific contact and process outcomes.
What if orientation can be reversed?
Mark the approved orientation and assess whether mistaken loading is possible. Ask the fixture owner to address it before release.
Can I approve from a finished photograph?
Use the agreed measurements and inspection conditions. Photos can show evidence when the sample, location and view are identified.
Should I check more than one specimen?
Use the project's sample plan and relevant dimensional or material variation. Record the population it covers.
What if an edge mark appears after unloading?
Preserve the original state and review before/after observations. Ask qualified owners to investigate handling, loading and process conditions.
What does Hisemi need at RFQ?
Provide the geometry, sample condition, allowed support areas, process and inspection criteria, and the documents needed for approval.
Request a workpiece-specific jig review
Send Hisemi the part drawing and approved process scope. Ask for a matching proposal and a defined qualification plan for the actual sample.

