A Wafer Process Sample Traveler for Incoming and Final Inspection

Nov 19, 2026

Leave a message

Jack
Jack
Hisemi editorial team
 

A wafer sample traveler should follow the physical sample from receipt through final inspection. It needs a stable wafer ID, a map of applicable measurement points and a record of every process or handling exception that changes the comparison. Without that chain, a convincing before-and-after thickness table might report different pieces, sides or points.

Hisemi's Wafer Lapping Polishing Machine is the equipment context for this guide. Hisemi lists 300, 350 and 420 mm plate diameter options. A plate dimension identifies a machine configuration, so confirm eligible wafer sizes and the handling arrangement for the exact trial. The traveler is the purchasing and engineering record used to connect a representative substrate and approved process to measurements. Equipment literature can inform the discussion, while the demonstration plan establishes which wafer materials, diameters, surfaces and reporting methods are actually in scope. Define inspection separately for each required property and use the exact units on every sheet.

Keep one sample ID

Link carrier movements, before-and-after maps and disposition to each wafer.

Hisemi wafer lapping and polishing machine

Hisemi wafer lapping and polishing machine · Hisemi lapping and polishing equipment

Start with an identity the wafer can keep

Decide how the sample will be identified on receipt, during processing and at return. If the project prohibits direct marking on the sample, keep the approved carrier or slot association under controlled handling. Record the incoming label and project identifier, and document every approved move between carriers. Incoming submittals should identify how the supplier and your lab refer to the same sample.

Include the substrate, nominal diameter, supplier lot and surface conditions called out on the order. Where the project needs an orientation cue, record the reference and capture it in the intake photographs. Note any physical condition issue and record its location in a way a later inspector can recognize. An image filename such as "sample after" becomes ambiguous as soon as another wafer enters the same job.

For parallel trials, distinguish the actual sample IDs from the proposed routes. If route A changes after the first piece, use new process evidence linked to the pieces that actually followed it. Preserve the initial assumptions so a mid-run process change cannot make originally planned data look like completed work.

Define comparable points before measuring anything

Ask the measurement owner to state which properties are required. Center thickness, total thickness variation and surface finish are distinct results, each with its own method. Where the specification requires thickness variation, keep valid high and low values and the map or scan that supports them. For surface finish, record the appropriate method and test area instead of borrowing the thickness points without review.

Set the coordinate system, orientation, instrument and units. Where a team uses a point map, record the expected locations and allowable exclusions, such as a project-defined edge zone. If an incoming sample cannot be measured at one point, flag the missing result and reason. If an instrument change is unavoidable, document the measurement team's comparison plan before using the two data sets together.

A receiving lab may have a convenient fast check and a different approved acceptance method. Keep the quick check identified and retain the acceptance record independently. A difference between methods is easier to investigate when both records identify the tool and conditions.

Include a blank for the measured face and units on any manually entered reading. When a customer evaluates a finish on one face and measures thickness through the wafer, make both definitions visible. Report the effective process route even if the process record is governed by separate confidentiality terms. For instance, the customer can be given an agreed route revision and sample evidence without receiving every internal setting. A cover sheet should identify what was supplied and who can access any additional data. Check those terms before dispatch so a missing attachment does not delay disposition after the customer receives the wafers.

Capture the handoff as a sequence

Process stage Required traveler entries Decision available from the record
Receiving Permanent job ID, supplier ID, carrier slot, condition and photographs Confirm the piece on the traveler is the piece delivered
Before processing Orientation, method, instrument, units, measurement map and results Establish the measurement basis for later comparison
Process Tool identification, route revision, fixture, operator and date Determine which configuration actually handled the sample
Final inspection Same point references where required, exclusion and exception notes Decide whether each result meets the documented rule
Return Updated carrier and slot, remaining conditions and results linked by ID Preserve identity through shipment and customer review

Keep calibration references or method checks with the file where the agreement requires them. Record the version on any imported readout, and keep raw readings distinct from calculated summaries. A processing supplier does not need copies of unrelated lab records. The point is to provide sufficient evidence for the customer to recognize which decision follows from which sample.

If the traveler's workflow changes midway, keep a timestamped line and the reason. For instance, a wafer condition may require a hold before it transfers to the next operation. The hold belongs between the relevant stages, with the approving owner's disposition. A final note weeks later is less effective when someone has to determine when the event happened.

Release the result with its conditions attached

As an illustrative example, suppose a wafer is measured before and after processing at its center and four approved off-center sites. One final off-center site cannot be measured because of an observed condition. The reviewer should save the other readings, flag the missing point and apply the project rule for an incomplete map. A calculated range from four points can describe those observations, but the acceptance report should explain what was omitted and whether a defined repeat is needed.

Display any images, maps and instrument exports with readable identifiers. If a wafer is returned to the customer and measured again, retain the customer's method as a separate data set. A compatible result may confirm the agreement. A disagreement calls for a review of sample identity, location, measurement methods and timing before anyone makes a correction.

For a later production lot, identify which demonstration evidence applies and which conditions have changed. A different wafer material or fixture arrangement may call for additional evaluation. A well-designed traveler lets the parties compare the new run with the pilot without assuming an equipment demonstration covers additional work.

Run a rehearsal of the document flow with a mock carrier record before accepting live samples. Ask the intake staff to assign a wafer ID, the processing team to record a route without losing the supplier identifier, and the inspector to follow it to the reported result. This is an administrative check. It often exposes incompatible lab labels or missing fields before costly samples move between rooms.

A practical release package can fit on a cover sheet with several attachments. Put wafer identity, current carrier slot, disposition and authorized reviewer at the top. Follow with links to the approved point map, the raw data and any relevant process evidence. Give each attachment its own revision or date so the latest report can be found after a controlled repeat.

Think through what happens if one sample cannot be returned in the original carrier. The agreement should say who authorizes a new carrier, how the individual wafer is identified and which records or images move with it. Preserve the original slot association in the final file. The customer's receiving inspector should be able to see the new reference before opening the shipment.

For repeat programs, compare the inspector's working form against the buyer's specification at each revision. A point name left over from another geometry can look valid while it refers to no physical location on the current wafer. If a coordinate reference moves, label the old and new maps and identify the runs to which they apply. Keep the incoming file once it has supported a trial review. A later template change should not rewrite the evidence that was actually used to release the work.

Sample inspection questions

Should the customer or the process supplier assign the sample ID?

Either can propose it. Agree on a stable identifier before receipt and record how it maps to the supplier lot, carrier slot and customer reference. Keep that mapping visible through return.

Can the final inspector use a different method from incoming inspection?

When methods differ, disclose the difference and determine how the results can be compared under the project plan. Keep each result with its method. Use the agreed acceptance method for disposition.

What if the carrier slot changes?

Record the prior slot, updated slot, sample identity, date and responsible operator under the approved handling procedure. Keep both locations in the traveler instead of overwriting the first.

How should a missing measurement be shown?

Mark the point and reason. Retain the available raw data and state whether the approved method permits a partial result or requires a repeat. Avoid leaving an unexplained blank.

Which items usually go in the final report?

Include the sample ID, route and measured condition, methods and units, comparison data, applicable disposition and exceptions. Link original maps and photos as required by the purchase or test plan.

Can a traveler serve as an equipment performance guarantee?

Use it as evidence of the stated sample, process and method. Product acceptance and equipment guarantees depend on the agreed criteria and contractual scope. Include the conditions when referring to the result later.

Set up a documented sample run

Send Hisemi the wafer material and geometry, target result and units, handling constraints, approved inspection points and proposed data package. Ask which lapping and polishing configuration can support the sample plan.

Contact Hisemi Technology

Technical references
Send Inquiry